Tripod vs. Rzeppa joint

Both are constant velocity joints. How the tripod and the Rzeppa joint work, what each allows in angle and plunge, and why KMP driveshafts for race cars use tripod joints.

The ball-type joint on most road-car driveshafts and the tripod joint that KMP Drivetrain Products uses in its motorsport driveshafts are both constant velocity (CV) joints. The term “CV joint” is often used for the ball type only, but it describes what the joint does, not how it is built. This article explains how the two designs work and where each one belongs.

What a constant velocity joint does

A CV joint transmits torque between two shafts while the angle between them changes. Constant velocity means that the output turns at the same rotational speed as the input, whatever the joint angle. That is the difference with the older universal joint: compact, but its output speed is not constant, and the deviation grows as the angle increases.

A traditional universal joint.

A driveshaft also changes length as the suspension moves through its travel. The joints therefore have to allow some axial movement as well, known as plunge.

The Rzeppa joint

The Rzeppa joint is the most widely known CV joint. Most road cars use it on one or both ends of the driveshaft. It has four parts: an outer race, an inner race, usually six balls, and a cage that holds the balls.

Parts in a Rzeppa joint.

The outer race is usually part of the output shaft or flange. The inner race has an internal spline and is mounted on the shaft. Both races have grooves that match the ball diameter. The grooves are curved, not straight, so the joint can run at an angle, and the cage keeps the balls in the grooves. When the input turns, the inner race presses the balls against the outer race and the joint rotates at the same speed on both sides, also at an angle.

Rzeppa joint assembly.

There are Rzeppa-type joints that plunge. Two common designs:

The tripod joint

A tripod joint does not use balls. Three rollers sit on a spider, which takes the place of the inner race. The rollers run on needle bearings and turn very freely.

Parts in a tripod joint.

The spider fits in a housing with three matching tracks. Like the outer race of a Rzeppa joint, the housing is usually part of a flange or shaft. The tracks let the joint run at an angle and move axially without interrupting the drive. The plunge length follows from the design of the housing, so it can be made longer or shorter while the other parts stay the same. Torque is transmitted in a comparable way to the Rzeppa joint: the spider loads the rollers, and the rollers load the housing.

Tripod joint assembly.

Angle or plunge

The main advantage of the Rzeppa joint is its larger articulation angle. That is why most cars use it on the wheel side of the driveshaft, and why it matters most on front-wheel-drive cars, where the outer joint has to follow both the steering and the suspension.

The tripod joint allows less angle but more plunge. A tripod joint or a plunging Rzeppa-type joint is therefore often used on the inboard side, so that the driveshaft as a whole can follow changes in both angle and length. Where a shaft has two joints of the same type, one end is usually fixed axially and the other end plunges. This differs between designs.

Whether a tripod joint can be used depends on the angle the joint has to run at. Suspension geometry, suspension travel and camber all play a part. A rally car, for example, can have so much suspension travel that the joint angle becomes too large. KMP measures the working angles and the installed length on the car with a measurement shaft before a driveshaft is specified.

Why tripod joints suit race cars

Compact for its strength

A tripod joint is more compact than a Rzeppa joint. For the same size it is the stronger joint; for the same strength it is smaller and lighter. Where space is limited, changing to a tripod joint can make a stronger driveshaft possible within the same space.

Less friction, less heat

The suspension of a race car moves constantly, and the joints move with it. Because the rollers run on needle bearings, a tripod joint generates less friction during that movement and therefore less heat. Under race conditions that can decide whether the grease in the joint keeps doing its work, which has a direct effect on the service life of the joint.

Serviceable

A tripod joint can be taken apart completely, inspected and serviced. A Rzeppa joint is usually replaced as a unit. Being able to check the condition of the joint between races lowers the risk of a retirement caused by a driveshaft failure.

Sealing

Whatever the type, a joint has to be sealed. A rubber or silicone boot keeps the grease in and moisture and debris out.

Summary

Tripod joint Rzeppa joint
Articulation angle Smaller Large
Plunge Built in; length set by the housing design Only in plunging versions (double offset, cross groove)
Size for a given strength More compact Larger
Friction and heat Lower Higher
Service Can be dismantled and serviced Usually replaced as a unit
Production Easy to adapt to an application More complex to produce

Both joints have their place. On a circuit car with limited suspension travel, the joint angles usually stay within what a tripod joint allows, and its strength for the package size and its serviceability then count in its favour. Which joint is appropriate differs per application and is decided case by case.

The KMP driveshafts for motorsport are listed under Driveshafts. Used shafts can be inspected and overhauled through the rebuild service. For an application that is not listed, contact KMP with the chassis code and the details of the car.

All tech articles