The S65 makes its power at the top of the rev range, and the standard 3.85 keeps the circuit speeds in the wide-ratio half of the gearbox. What the KMP ratios from 3.73 to 5.43 change, and how to pick one.
The BMW E9x M3 left the factory with a 3.85 final drive, chosen for a car that had to reach a limited 250 km/h and stay civil on the motorway. On a circuit that ratio leaves the top of the gearbox unused. KMP builds the final drive for this axle in ratios from 3.73 to 5.43, so there is a lot of room to change it. This article shows what the standard gearing does, what a shorter ratio changes, and how to pick one.
The engine and gearbox data come from BMW’s own service training material for the car. The general mechanism of a final drive change is covered in what a 3.91 final drive changes on the F80 M3; this article is about what is different on the naturally aspirated E9x.
The S65B40 makes 400 Nm at 3,900 rpm and 414 hp at 8,300 rpm, with the limiter at 8,400 rpm. Those two numbers are worth putting side by side, because power is torque times engine speed:
The top panel shows why those two figures are so far apart. The torque curve is almost a straight line: from 3,000 to 7,200 rpm it never leaves the 390-401 Nm band. An engine with flat torque makes power in direct proportion to how fast it is turning, which is why the lower panel climbs the way it does, nearly to the limiter.
The engine makes nearly twice as much power at 8,300 rpm as it does where its torque peaks. That is the whole character of the car: the torque figure is modest for a four-litre V8, and the performance comes from engine speed.
BMW draws both engines on one diagram in the same training material, which makes the difference easy to see. The S55 of the F80 M3 is the opposite kind of engine: 550 Nm from 1,850 rpm, a plateau that is simply there, and 425 hp at 7,300 rpm. The S65 peaks at 400 Nm and has to be taken to 8,300 rpm for its 414 hp.
Both engines on one engine-speed axis, read off BMW’s own comparison diagram. Torque and power each get their own panel; the dashed lines are the two rev limiters.The lower panel is the one to read. At 4,000 rpm the S55 is already making 308 hp and the S65 225 hp; the V8 has to be at 5,560 rpm before it matches what the turbo six gives at 4,000 rpm. Each engine reaches half of its own peak power in a different place too: 2,760 rpm for the S55, 3,690 rpm for the S65.
That is the case for gearing in one picture. On the F80 the power is spread over most of the rev range, so where the needle sits matters less. On the E9x it sits at the top, and a final drive that keeps the engine up there is worth more.
| Gear | 1st | 2nd | 3rd | 4th | 5th | 6th | Final drive |
|---|---|---|---|---|---|---|---|
| E9x M3 (GS6-53BZ) | 4.055 | 2.396 | 1.582 | 1.192 | 1.000 | 0.872 | 3.85 |
| E46 M3 (S6S420G) | 4.227 | 2.528 | 1.669 | 1.226 | 1.000 | 0.828 | 3.64 |
The E46 M3 ratios are there for comparison: the two gearboxes are close relatives and the car runs a 3.64 final drive of its own, so what follows applies to it in much the same way. Look at how the steps between the gears change as you go up:
| Upshift | Step | Engine speed after the upshift, from 8,400 rpm |
|---|---|---|
| 1 to 2 | 1.69 | 4,960 rpm |
| 2 to 3 | 1.51 | 5,550 rpm |
| 3 to 4 | 1.33 | 6,330 rpm |
| 4 to 5 | 1.19 | 7,050 rpm |
| 5 to 6 | 1.15 | 7,320 rpm |
First to second is a big step and drops the engine to about 4,960 rpm, a long way under the 8,300 rpm where the power is. Second to third is nearly as wide. From fourth gear on, the steps are small and the engine stays above 7,050 rpm.
So the gearbox has a wide-ratio bottom half and a close-ratio top half. Which half you drive in depends on the final drive.
With the standard 3.85, this is how far each gear reaches at 8,400 rpm, against a 4.88 as an example of a circuit ratio.
Speed in each gear at 8,400 rpm. With the standard final drive the last two gears run past the speed the car is limited to.With 3.85 the car reaches its 250 km/h limit part way through 5th gear, and 6th is a motorway gear that a circuit never asks for. On most circuits it never gets past 4th, which is exactly the wide-ratio half of the gearbox.
With 4.88, sixth gear tops out at about 249 km/h. All six gears come into use, and the ones carrying the car through the middle of its speed range are the closely spaced ones.
The next figure makes that concrete. Each line is one gear: it shows what the engine is doing at a given road speed. The shaded band is an example circuit that runs between 70 and 170 km/h.
Engine speed against road speed, one line per gear. The steeper the line, the shorter the gear. The dashed lines mark the torque peak and the power peak.Across that band the standard car runs in 2nd and 3rd gear, with a single step of 1.51 between them. With 4.88 the same stretch of road is covered by 2nd, 3rd and 4th gear, with steps of 1.51 and 1.33. The car has moved up into the closely spaced half of the gearbox, and the gaps it drives through are smaller.
The effect is easiest to see at one speed. At 120 km/h the standard car is in 3rd gear at about 5,800 rpm. With 4.88 it is in 3rd gear at about 7,360 rpm, some 1,550 rpm higher and much closer to the 8,300 rpm where the engine makes its power.
Put that back on the full load curve in the first figure and it stops being an abstraction. At 5,800 rpm the engine has about 322 hp to give; at 7,360 rpm it has about 401 hp. Same corner, same throttle pedal, roughly 79 hp more, and none of it from touching the engine. That is the whole point of the exercise on a car like this.
It cannot make the gaps in the gearbox smaller. Where the engine lands after an upshift follows from the ratio between two gears, and the final drive multiplies both by the same number, so it cancels out. The 5,550 rpm after a second-to-third shift stays 5,550 rpm whatever final drive is fitted. Only a different gear set changes that.
What the final drive changes is the road speed at which each gear does its work, and with it which gears a given circuit actually uses. On this car that is worth a great deal, because the difference between the wide-ratio and the close-ratio half of the gearbox is large.
The table gives the available ratios, the change in torque at the wheels against the standard 3.85, and where 3rd and 6th gear reach at 8,400 rpm.
| Final drive | Torque at the wheels | 3rd gear | 6th gear |
|---|---|---|---|
| 3.73 | -3% | 179 km/h | 325 km/h |
| 3.91 | +2% | 171 km/h | 310 km/h |
| 4.10 | +6% | 163 km/h | 296 km/h |
| 4.50 | +17% | 149 km/h | 270 km/h |
| 4.75 | +23% | 141 km/h | 255 km/h |
| 4.88 | +27% | 137 km/h | 249 km/h |
| 5.00 | +30% | 134 km/h | 243 km/h |
| 5.28 | +37% | 127 km/h | 230 km/h |
| 5.29 | +37% | 126 km/h | 229 km/h |
| 5.43 | +41% | 123 km/h | 223 km/h |
Reading it the other way round is more useful than picking a percentage. Take the fastest point of the circuits the car runs on, and choose the ratio that puts that speed near the top of a gear rather than just over a shift point. Then check the slowest corner against first and second gear.
What you give up is the same in every case: the engine turns faster at any road speed, so a road drive is noisier and thirstier, and the shortest ratios make first gear close to useless. Wheel torque rises with the ratio, so the driveshafts, the flanges and the differential see more load.
The KMP 210 final drive is the crown wheel and pinion for this axle, available as a KMP Motorsport part or in OEM quality. It also fits the E36 M3, the E34 M5 and the E39 M5.
Most cars are better served by the complete motorsport differential for the E92 M3: a Drexler plated limited slip differential and the chosen final drive, built and set up as one unit, as a send-in conversion, an exchange unit or a complete purchase. On a car that still has the standard differential, that plated LSD is the larger gain of the two; the final drive costs almost nothing extra once the unit is open. The same is available for the E46 M3.
More torque at the wheels is more load on everything behind the differential, so it is worth looking at the E92 M3 driveshafts at the same time. Units that have been raced can be inspected and reset through the rebuild service, and the bearing and seal kits for this differential are in the catalogue.
For help choosing a ratio, contact KMP with the circuits the car runs on and, if there is any, a data log showing the engine speed out of the main corners. That turns the choice from an estimate into a calculation.