BMW F80 M3: what a 3.91 final drive changes

13% more torque at the wheels in every gear, shorter gears and the same top speed. What a 3.91 final drive changes on the F80 M3 DCT, and what it does not, in figures.

The BMW F80 M3 leaves the factory with a 3.46 final drive. For track use, a common change is a shorter one: 3.91. This article shows what that does to the car, using the F80 M3 with the seven-speed DCT gearbox as the example. No formulas are needed to follow it; the calculations behind the figures are listed at the end. The conclusions hold for this engine and this gearbox, and the section on older M cars explains why they do not simply carry over to an E-series M3.

The short version

What the final drive does

The final drive is the last pair of gears in the driveline: the pinion and the crown wheel in the differential. Whatever gear the gearbox is in, the drive always passes through it. Changing the final drive therefore changes all seven gears at once, by the same percentage.

A bicycle makes a good comparison. Fit a smaller chainring at the front and every gear at the back becomes lighter: you pull away harder, and you run out of pedalling speed sooner. A shorter final drive (a higher number, such as 3.91 where 3.46 was fitted) does the same to a car.

The same engine torque in the same gear: the final drive decides how much of it arrives at the wheels, and how fast the wheels turn. Values before driveline losses.

The gearing of the F80 M3 DCT

Gear 1st 2nd 3rd 4th 5th 6th 7th Final drive
Ratio 4.806 2.593 1.701 1.277 1.000 0.844 0.671 3.462

Two things stand out. Fifth gear is 1.000, a direct drive, and 6th and 7th are both overdrives. Seventh in particular is a cruising gear: it keeps the engine speed low on the motorway and helps fuel consumption and emissions. On a circuit it is hardly used.

Speed in each gear

The chart shows how fast the car goes in each gear at 7,300 rpm, the end of the engine’s power band. With the 3.91 final drive every bar is 11.5% shorter: you change up earlier, and on most circuits you use one gear more.

Speed at 7,300 rpm in each gear. The bars for 6th and 7th run past the top speed of the car: those speeds exist on paper only.

With the standard final drive, 7th gear would be good for almost 400 km/h at 7,300 rpm. The car never gets there. That is how long the standard gearing is.

Force at the wheels

What accelerates a car is the force with which the rear tyres push it forward. The chart shows that force for 3rd to 7th gear, with both final drives. The higher a line, the harder the car accelerates at that speed in that gear.

Force at the rear wheels in 3rd to 7th gear with the full engine torque. Each line starts at 1,850 rpm. The flat part is the torque plateau of the engine; on the dark curve the engine is at full power. Where a line meets the dashed resistance line, the car has reached its top speed in that gear.

Two things can be read from it.

On the flat part of each line, the 3.91 car has 13% more force at the same road speed. This is the engine’s torque plateau, up to 5,500 rpm. An example: out of a corner at 90 km/h in 3rd gear, the standard car has about 8.3 kN at the wheels and the 3.91 car about 9.4 kN. The engine is also turning faster, about 4,750 rpm where it would be at 4,210 rpm, so it is closer to its power band.

On the dark curve, both cars are the same. Above 5,500 rpm the engine delivers its full power, and at full power the force at a given road speed is the same whatever the gearing. It is worth seeing why, because this is where the 13% figure stops applying. At a given road speed the 3.91 car’s engine turns 13% faster, and at constant power 13% more rpm means 13% less engine torque. In 4th gear at 160 km/h, the standard engine makes 539 Nm at 5,620 rpm and the 3.91 engine makes 477 Nm at 6,340 rpm. The gearing multiplies the smaller number by the larger ratio, the two cancel, and both cars put 6.1 kN on the road. A shorter final drive does not add power; it lets the engine reach its power band sooner in each gear.

The table below shows the whole sum for 4th gear, including the step in the middle that is easy to skip over: engine torque × 1.277 (4th gear) × the final drive × 86% driveline efficiency = the torque at the rear wheels. That torque divided by the tyre radius is the force on the road.

Speed in 4th Final drive Engine speed Engine torque Torque at the wheel Force
130 km/h 3.46 4,560 rpm 550 Nm 2,091 Nm 6.3 kN
3.91 5,150 rpm 550 Nm 2,362 Nm 7.1 kN
150 km/h 3.46 5,270 rpm 550 Nm 2,091 Nm 6.3 kN
3.91 5,950 rpm 509 Nm 2,186 Nm 6.5 kN
160 km/h 3.46 5,620 rpm 539 Nm 2,049 Nm 6.1 kN
3.91 6,340 rpm 477 Nm 2,049 Nm 6.1 kN

Nowhere in the table does the 3.91 car have less torque at the wheels. At 130 km/h it has 13% more; at 160 km/h it has the same. Look at that last pair: the 3.91 engine makes 62 Nm less, but multiplies it by a 13% larger ratio, and the same torque arrives at the wheel. The lower engine torque is not a loss; it is the same 317 kW spread over more revolutions. The 13% is a maximum, not a constant.

That is also why the gain depends on how the car is driven. Flat out through the gears from 100 to 200 km/h, changing up at 7,300 rpm every time, the calculation gives practically the same time for both: 8.8 seconds with 3.91 and 8.9 seconds with 3.46. With seven closely spaced gears, the engine is back in its power band after every upshift anyway. On a circuit the car spends much of the lap below that: on the way out of corners, and in a gear that is kept for the next corner. That is where the shorter final drive is felt. These are calculated values without gear change times, meant for comparison, not as measured performance figures.

Why the standard gearing already works well

The reason the flat-out difference is so small lies in the gearbox itself. The table shows where the engine lands after each upshift at 7,300 rpm.

Upshift Step Engine speed after the upshift
2 to 3 1.52 4,790 rpm (below the power band)
3 to 4 1.33 5,480 rpm
4 to 5 1.28 5,720 rpm
5 to 6 1.18 6,160 rpm
6 to 7 1.26 5,800 rpm

From 3rd gear up, every upshift puts the engine back at around 5,500 rpm or higher, the point where full power begins. Only the step from 2nd to 3rd lands well below it. The gearbox is matched to the engine.

And this is what decides the whole question: those numbers follow from the steps between the gears alone, never from the final drive. The final drive multiplies every gear by the same factor, so it cancels out. A different final drive cannot change where the engine lands after an upshift. Only a different gear set can.

First and second gear

In the lowest gears the limit is not the gearing but the tyres. In 1st gear the calculated force at the wheels is about 24 kN with the standard final drive, more than the weight of the whole car (about 16 kN). No tyre can transmit that. A shorter final drive adds nothing there. The gain is in 3rd gear and up, which is where a circuit lap is driven.

What about top speed?

A shorter final drive lowers the speed in every gear, so it seems obvious that the top speed drops. In practice it hardly does, because the standard car does not reach its top speed at maximum rpm in top gear in the first place. Air resistance stops it earlier.

These are calculated values for a car without a speed limiter.

What you give up

When is a 3.91 worth fitting?

Put together, a shorter final drive is not by itself a lap-time upgrade on this car. It earns its place in three situations.

  1. The differential is coming out anyway. On a car built for the track, replacing the electronically controlled Active M differential with a plated limited slip differential is the larger step. The final drive sits in the same unit, so fitting it at that moment costs almost no extra work.
  2. The gears do not match the circuit. If the car reaches the limiter just before a braking zone, or an important corner falls awkwardly between two gears, moving every gear 11.5% down the speed scale can solve it. This is circuit-specific: what helps at one track can work against you at another.
  3. The car has gained weight or larger tyres. A cage, ballast or a larger rolling diameter all make the standard gearing effectively longer. A shorter final drive gives back what was lost.

And the other side of it:

On a car still running the standard differential and standard driveshafts, those are the parts to address first. The final drive is best fitted along with them.

Older M cars behave differently

All of the above follows from the engine in the F80: turbocharged, with 550 Nm available from 1,850 rpm. That broad, flat torque plateau is what makes the standard gearing work as well as it does, and it is why the car still pulls cleanly well below its power band. The G-series M cars are built along the same lines.

The naturally aspirated M engines of the E-series are a different case, and BMW draws the two side by side in the same training material.

Both engines as BMW publishes them. The dashed line is the simple engine model the rest of this page calculates with, 550 Nm to 5,500 rpm and then constant power: it follows the measured curve to within 1.2 Nm on average over the 1,850-7,300 rpm band this article uses.

The S65B40 of the E9x M3 reaches 414 hp, but only at 8,300 rpm, and its torque never passes 400 Nm against the 550 Nm here. At 4,000 rpm the S55 is making 308 hp and the V8 225 hp; the V8 has to be taken to 5,560 rpm before it matches that. Each engine is at half of its own peak power in a different place as well: 2,760 rpm here, 3,690 rpm on the S65. With less torque to lean on, that engine depends far more on revs for its thrust. It also has one gear fewer and wider steps between them: 4.055, 2.396, 1.582, 1.192, 1.000 and 0.872, on a 3.85 final drive. After an upshift the engine lands a long way below the speed at which it makes its power, and with six ratios there is often no better gear to pick instead.

Shortening the final drive raises the engine speed at every road speed. On an engine built like that it moves the engine towards the part of the rev range where its power is, which is worth more than it is on the F80. The reasoning on this page therefore does not transfer one to one to an E46 or E9x M3; that car has its own comparison in BMW E92 M3: choosing a final drive. The KMP final drives for the BMW 168, 188 and 210 axles are listed under Differentials.

3.91 or 4.11?

KMP makes the final drive for the BMW 220 rear axle of the F87 M2, F80 M3 and F82/F83 M4 in two ratios: 3.91 and 4.11. Everything above applies to 4.11 as well, with larger steps in both directions: 19% more torque at the wheels than standard, and correspondingly shorter gears. Which one suits a car depends on the circuits it runs on and on how much road use it still sees.

What the conversion involves

The KMP Motorsport final drive for the F-series fits the OEM differential without machining and is for use with steel driveshafts. It is also available built into a complete motorsport differential with a Drexler plated limited slip differential, as a send-in conversion, an exchange unit or a complete purchase. Background on final drives in general is in Why change your final drive?

For advice on the ratio for a specific car and circuit, contact KMP.

How the figures were calculated

All tech articles