Plated limited slip differential explained

From open differential to clutch-pack LSD: the components, the three stages of clutch pack loading, friction and stick-slip, and the three variables of a setup.

Almost every car has one or more differentials in its driveline. A differential lets the driven wheels turn at different speeds: in a corner the inner wheel travels a shorter distance than the outer wheel and has to turn slower. Without that freedom the car would resist turning in and understeer. This article describes how a plated (clutch-pack) limited slip differential works, starting from the open differential it is based on.

The limitation of an open differential

An open differential works well on a road car but not in motorsport. By the nature of the bevel gear design, the torque at both wheels is always the same. That limits how much torque the car can put down. If one wheel loses traction, only a small amount of torque is needed to turn it. The other wheel receives the same low torque, so the total torque transmitted to the road is low.

Most competition cars therefore use a clutch-pack limited slip differential. In this type, torque can pass directly from the differential housing to the side gears through the clutch packs, bypassing the differential gear set.

Torque flow in an open differential

Open differential: section view, and the speeds when driving straight and in a corner.

Components of a plated limited slip differential

A plated limited slip differential is essentially a bevel gear differential combined with friction plates that can lock the side gears to the differential cage, partially or fully. The higher the torque, the greater the locking effect.

The components of a plated limited slip differential.

The friction plates usually have a spline connection to the side gears. The outer plates usually have a sliding connection to the differential cage. The outer plates therefore always turn at the speed of the cage, and the friction plates at the speed of the side gears and driveshafts. Pressure rings sit between the bevel gear shaft and the clutch packs, and Belleville springs load the packs axially.

Outer plates with an external spline, friction plates with an internal spline, and the Belleville washer.

Three stages of clutch pack loading

1. Belleville spring action (preload)

The Belleville springs put an axial load on the clutch plates. This produces a small amount of friction that tends to lock the side gear, and with it the driveshaft, to the differential cage when the transmitted torque is very low. It ensures that some drive torque still reaches the wheel that is not spinning. The preload gives the basic friction torque of the differential.

2. Bevel gear separating force

Under load, the bevel gears in the cage tend to push the side gears outwards. The extra outward force that arises when one wheel starts to spin is passed through the pressure rings to the clutch packs. Both sets of plates are clamped together, which resists relative movement between the side gears and the cage.

3. Pressure angle action

As the torque increases further, a third stage comes in. The bevel gear shaft sits between ramps in the two pressure rings. When torque is applied, the reaction of the shaft on these ramps forces the pressure rings outwards, squeezing each clutch pack and increasing the locking effect.

The angle of the ramps is the pressure angle: the lower the angle, the higher the outward axial force. The pressure angles are often different for drive and for coast. Which angles are chosen depends on many factors, including the weight and dimensions of the car, the engine torque and the type of racing. On the coast side, the torque that loads the differential is the engine braking torque only.

The bevel gear shaft between the ramps of the pressure rings, and the effect of the pressure angle on the axial force.

Friction and stick-slip

The friction force in the clutch pack is the friction coefficient multiplied by the force that clamps the plates. A high friction force makes the left and right wheel try to turn at the same speed. On corner entry and on the overrun this shows as understeer; under power it can turn into oversteer on a rear-wheel-drive car.

Depending on the friction material there is a difference between static friction, when the plates do not move relative to each other, and kinetic friction, when they slide. More force is needed to start the movement than to maintain it. When the applied force is close to the static friction, the plates alternately stick and slip, which is felt as shudder. Friction plates in limited slip differentials are often coated with a sintered or molybdenum surface. Both have good stick-slip properties and a high friction coefficient.

Setting up a plated LSD: three variables

A plated limited slip differential is set up with three variables:

There is no formula that produces the best setup. It depends on the car, the track and the driver, and choosing it takes experience. With the full details of the car, a specialist can give a sound base setup to start from.

KMP Drivetrain Products supplies plated limited slip differentials as complete, set-up units, together with the plates, spacers and other rebuild parts; see Differentials. Units that have been raced can be inspected and reset through the rebuild service. How a plated LSD compares with a geared differential is covered in Torsen vs. plated limited slip differential.

All tech articles